LM3886 GND pin
Pagina 1 di 1
LM3886 GND pin
Forse sono distratto ma l'unico riferimento al pin 7 GND del LM3886 che ho trovato sul datasheet è questo:
Note 5: All voltages are measured with respect to the GND pin (pin 7), unless otherwise specified.
Sullo schema equivalente non viene riportato e non capisco sattamente la sua funzione, se è un riferimento di tensione, se transitano correnti e di che entità ecc... E quindi se lo devo collegare necessariamente al centro stella della massa,se non ha importanza o se magari e meglio collegarlo altrove.
Qualcuno ne sa di più o sa se esiste uno schema dell'integrato da cui si capisce a cosa collegato internamente?
Altro dubbio m viene sul doppio pin per il V+, ma li collego entrambi all'alimentatore e me ne frego
Note 5: All voltages are measured with respect to the GND pin (pin 7), unless otherwise specified.
Sullo schema equivalente non viene riportato e non capisco sattamente la sua funzione, se è un riferimento di tensione, se transitano correnti e di che entità ecc... E quindi se lo devo collegare necessariamente al centro stella della massa,se non ha importanza o se magari e meglio collegarlo altrove.
Qualcuno ne sa di più o sa se esiste uno schema dell'integrato da cui si capisce a cosa collegato internamente?
Altro dubbio m viene sul doppio pin per il V+, ma li collego entrambi all'alimentatore e me ne frego
Fabio- Membro classe argento
- Data d'iscrizione : 02.11.08
Numero di messaggi : 2518
Località : Roma
Provincia : pessimo
Occupazione/Hobby : informatico aziendale / ozio
Impianto : in firma
Re: LM3886 GND pin
Sono riuscito a trovare questo su un forum:
...............
From the datasheet and internal schematic of the LM3886 it can be seen that the GND pin has several functions.
1 - its voltage vs. the V- pin is monitored, keeping the chip in mute mode when it is less than 9V.
2 - it defines the output potential in mute/startup mode. Note the 10k on the left side of the inner diff amplifier. This diff provides a closed feedback loop in mute mode with the right hand 10k and the clamping diodes. These diodes go to ground, thus in normal operation there is a current path from the output to GND, via the 10k, about 0.1mA per Volt of output voltage.
3 - it's the reference potential for the mute logic. When current is drawn from the mute pin (towards V-) in the ON mode, the startup diff's current source gets turned off by the grounded base transistor on the left. The GND pin provides the base current for it.
4 - there must be something missing here, because from the single-supply schematic I realize that the GND pin shall only sink current in normal operation. OTOH, that schem might be wrong/flawed.
Especially point #2 indicates that the current into/out of the GND pin should not be routed to signal GND, in theory, as this nonlinear current might contaminate the signal GND. In fact it's so small (well below 10mA) that this is not a problem in a proper design/layout. Likewise, if this GND pin carries some noise, it won't affect operation -- but avoid excessive HF noise, of course.
So, my 2 cts:
If you have the option, don't bond it to signal GND. But don't sacrfice a good layout just for that tidbit.
Regards, Klaus
..........................
Non so a quale datasheet faccia riferimento, ma facciamo a fidarsi.
...............
From the datasheet and internal schematic of the LM3886 it can be seen that the GND pin has several functions.
1 - its voltage vs. the V- pin is monitored, keeping the chip in mute mode when it is less than 9V.
2 - it defines the output potential in mute/startup mode. Note the 10k on the left side of the inner diff amplifier. This diff provides a closed feedback loop in mute mode with the right hand 10k and the clamping diodes. These diodes go to ground, thus in normal operation there is a current path from the output to GND, via the 10k, about 0.1mA per Volt of output voltage.
3 - it's the reference potential for the mute logic. When current is drawn from the mute pin (towards V-) in the ON mode, the startup diff's current source gets turned off by the grounded base transistor on the left. The GND pin provides the base current for it.
4 - there must be something missing here, because from the single-supply schematic I realize that the GND pin shall only sink current in normal operation. OTOH, that schem might be wrong/flawed.
Especially point #2 indicates that the current into/out of the GND pin should not be routed to signal GND, in theory, as this nonlinear current might contaminate the signal GND. In fact it's so small (well below 10mA) that this is not a problem in a proper design/layout. Likewise, if this GND pin carries some noise, it won't affect operation -- but avoid excessive HF noise, of course.
So, my 2 cts:
If you have the option, don't bond it to signal GND. But don't sacrfice a good layout just for that tidbit.
Regards, Klaus
..........................
Non so a quale datasheet faccia riferimento, ma facciamo a fidarsi.
Fabio- Membro classe argento
- Data d'iscrizione : 02.11.08
Numero di messaggi : 2518
Località : Roma
Provincia : pessimo
Occupazione/Hobby : informatico aziendale / ozio
Impianto : in firma
Pagina 1 di 1
Permessi in questa sezione del forum:
Non puoi rispondere agli argomenti in questo forum.
|
|
Oggi alle 18:53 Da FilippoTN
» Kenwood KA8100: 45 anni e sentirli tutti
Oggi alle 14:58 Da arthur dent
» compatibilità DIN-RCA
Oggi alle 13:38 Da GAMBACORTA STEFANO
» problema amplificatore kenwood ka-56
Oggi alle 13:25 Da salvo93
» Thorens TD 160B mkII
Oggi alle 11:57 Da philball1959
» Thorens TD126 MKIII
Oggi alle 10:01 Da philball1959
» cambio Stilo o Testina
Oggi alle 9:58 Da philball1959
» Fruscio ed effetto popcorn Piastra Teac A-103
Ieri alle 23:22 Da Alessandro Gurato
» Cerca l'officina riparazioni MI-BG. Ho bisogno di aiuto
Ieri alle 9:40 Da Alessandro Gurato
» Sostanza appiccicosa/gommosa x altoparlanti
Mer 24 Apr 2024 - 18:44 Da THC
» RME Digiface
Mer 24 Apr 2024 - 13:06 Da fritznet
» MINI AMPLIFICATORE CLASSE D - CHE PASSIONE !!!
Mer 24 Apr 2024 - 10:47 Da refrank71
» Consiglio su Topping E30II vs Ifi Zen DAC V2
Mar 23 Apr 2024 - 18:36 Da PiLuxNiEn
» Sto imapzzendo per trovare un cavo dall'amplificatore alle casse.
Mar 23 Apr 2024 - 17:31 Da gmasi1971
» [TP + Spedizione] Vendo Wharfedale Denton 85th Black Edition
Mar 23 Apr 2024 - 7:52 Da Sanfilippo Roberto
» Stand diffusori homemade
Lun 22 Apr 2024 - 22:12 Da PiLuxNiEn
» KEF R3 META
Lun 22 Apr 2024 - 10:19 Da giucam61
» Volume che scompare
Dom 21 Apr 2024 - 11:39 Da Alessandro Gurato
» TRIANGLE THETA SIGNATURE
Dom 21 Apr 2024 - 6:36 Da AndreaCD
» Consiglio per Diffusori JBL
Dom 21 Apr 2024 - 1:45 Da TRIPLALLOSCADERE
» Consigli: acquisto giradischi Pioneer.....cinghia o trazione diretta? Modello?
Sab 20 Apr 2024 - 19:41 Da TRIPLALLOSCADERE
» Vendo Thorens td 115
Sab 20 Apr 2024 - 13:31 Da Alessandro Gurato
» Sommatore passivo
Sab 20 Apr 2024 - 8:54 Da RUR
» Elenco casse a 3 vie con woofer da 30cm in sospensione pneumatica
Gio 18 Apr 2024 - 15:17 Da Marco Ravich
» Samar PMT/1 prova messa a terra
Gio 18 Apr 2024 - 11:35 Da Gedeone
» Che dischi avete amato, ma non ascoltate più?
Mer 17 Apr 2024 - 23:53 Da Quaiozi!
» cuffie Sennheiser
Mer 17 Apr 2024 - 8:29 Da Quaiozi!
» Vendo Pioneer A- 400
Mar 16 Apr 2024 - 16:02 Da Marcus
» Schiocco dalle casse ad accensione componenti vintage e non solo
Mar 16 Apr 2024 - 10:54 Da Simone63
» Consiglio acquisto diffusori
Lun 15 Apr 2024 - 22:43 Da Zio